.10” Companies TABLE Found MODEL: KC-10TChemical INSTRUCTION MANUAL COPYRIGHT © 2008 ALL Privileges RESERVED BY Full CANADA TOOLS INC.Evidence OF PURCHASE Please maintain your dated proof of purchase for guarantee and servicing purposes. REPLACEMENT PARTS Replacement parts for this Desk Saw with fresh blade safeguard are accessible at our authorized King Europe service centers across Europe. LIMITED Device WARRANTY Master Canada makes every work to make certain that this item meets high high quality and strength standards.Common SAFETY INSTRUCTIONS FOR POWER TOOLS 1. KNOW YOUR Device 15. Detachment TOOLS. Study and understand the owners manual and brands attached to Before servicing, when altering add-ons or accessories.
Find out its program and limitations as properly as its 16.SPECIFIC Security INSTRUCTIONS, SPECIFICATIONS Desk OF Items 1. ALWAYS USE A GUARD. DIRECTION OF FEED.
Always make use of a guard, splitter and anti-kickback fingertips on all Feed function into the cutter or cutter against the direction or “thru-sawing” procedures. Thru-sawing procedures are those turn of the edge or cutter machine.ASSEMBLY Equipment PROVIDED FOR ASSEMBLY 1. Arbor-blade guard bracket wrench.
12mm mixture wrench. Two aIlen wrenches. ADDITIONAL TOOLS REQUIRED 1. Huge flat-head screwdriver. Phillips #1 point screwdriver Be aware: The make use of of sockéts with a ratchét will lessen the assembly time required.ASSEMBLY Putting together GUIDE Side rails 1. Assemble the front and rear guide rails to the table using the special screws (A) and spacers (C), as shown in Fig.5.
The manual rail with the calibrations goes on the front of the table and these calibrations are to become on the top side.ASSEMBLY ASSEMBLING MOTOR, MOTOR Dish AND GUARD BRACKET Create certain the motor is DISCONNECTED from the power supply and assembled as follows: 1. Assemble the 2-1/2” buggy bolt (A) and washing machine (C) to the pulley safeguard bracket using nut (T) as shown in Fig.10. 2.ASSEMBLY Putting together BELT AND PULLEY COVER 1. Assemble the V-belt to the motor and arbor pulleys. Making use of a direct edge, align the twó pulleys as demonstrated in Fig.15. If required move the motor and/or motor pulley for appropriate alignment.
Location spacer (A), cleaner (M) and side enthusiast (M) on screw as proven in Fig.16.ELECTRICAL CONNECTIONS ADJUSTMENTS WARNING! ALL ELECTRICAL CONNECTIONS MUST Become Carried out BY A QUALIFIED ELECTRICIAN. Failing TO COMPLY Might Outcome IN SERIOUS Damage! ALL Modifications OR Fixes MUST BE Carried out WITH THE TABLE Found DISCONNECTED FROM THE Strength SOURCE.
FAILURE TO COMPLY Might Outcome IN SERIOUS Injuries! CONNECTING Found TO Strength Supply A distinct electrical circuit should be used for your strength tools.ADJUSTMENTS BLADE RAISING AND TILTING System To raise or lower the saw knife, loosen the locking mechanism button (A), Fig.23 and switch the bringing up handwheel (T).
With the exception of hollow ground blades. The blade should become raised 1/8' to 1/4' above the surface of the material being reduce.Functions REMOVING Found Edge When getting rid of saw cutting blades from the found, make sure the found is shut off from the power source. Position in top of the desk saw, get rid of the desk insert, location a block of real wood against the entrance of the saw edge and making use of the arbor nut wrench, convert the arbor nut towards you.Functions If the ripped function is much less than 3 inches wide, á push-stick shouId be used tó complete the féed, as shówn in Fig.29. A typical push-stick is certainly demonstrated in Fig.30, and can be easily made from scrap materials. When tearing 2 in . or narrower, maké an auxiliary guidé and fastén it to thé rip fence, ánd use á push-stick.OPERATIONS It will be required when making use of the moulding cutterhead to include wood- dealing with to one or both edges of the rip fencing. The wood-facing will be attached to the fence with hardwood screws.
3/4' stock is ideal for most work. Place the wood-fácing over the cuttérhead with the cuttérhead below the surface area of the table.TROUBLESHOOTING PROBLEM SOLUTION Found WILL NOT Begin 1.
Noticed not plugged in. Blend taken or signal breaker tripped.
Grizzly Tsc-10l Manual Free
Replace fuse or reset circuit breaker. Wire damaged.
Grizzly Tsc-10l Manual 2016
Have cord replaced by a licensed electrician.
The wafers used by thé TSCD-II weIder temperature up to 300 ̊Chemical, preserving sterility during reducing and welding without allowing particulates or chemical deposits to type in the pipes. The style enables fast, one-handed operation, and long lasting materials endure up to demanding make use of. Maintains a closed system. Ties any combination of tubing: wet-to-wét, dry-tó-dry, wet-tó-dry. Provides automatic wafer replacement. Features an interconnected cIamp for one-handéd procedure. Guides use and displays procedure on the screen.
Supports bags with detachable shelves. Reduces the risk of jellies with a wafer monitor and a Iarge used-wafer grasp box. Produces welds that meet or surpass the tensile strength needs of ISO 3826-1The TSCD-II welder is obtainable in select markets.